Just how to Replace a Bath Tub ( Guide).
Just how to Replace a Bath Tub ( Guide).
Blog Article
Do you find yourself interested in selective information around How to Install a Bathtub?
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open a wall to eliminate the old bathtub and also place the new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will certainly require an assistant to move out the old tub and set in the new one. Make certain you have actually certified on your own for the work and also fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to think about utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube links.
This article will aid you set up a new bath tub in your bathroom if you have actually currently gotten a new bathtub and also don't require to change the arrangement of your previous water pipelines.
Your devices and also material checklist should make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be quite bothersome because of the restricted access that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a cloth ready for the staying water that will originate from the pipelines. As soon as the supply pipes have been removed, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from transforming throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Before moving on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in place in between the faucet as well as the sink. Safeguard the tap in position with the manufacturer given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed setting. The wood boards are useful in uniformly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level as well as readjusting the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water supply and inspect all joints as well as brand-new pipework for leaks and also tighten them if needed. Load the bath tub and also inspect the overflow outlet as well as the normal outlet for leakages.
Lastly, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also sealing around the bathtub should wait until the tub has been utilized a minimum of when as this will certainly resolve it right into its last placement.
Planning for the Installation
Firstly, the sustaining frame provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bathtub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now prepare to be suited its final position.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a stiff seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, bring about problems with wetness and possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that report about A Step-by-Step Guide to Installing a Bathtub from a good friend on our other domain. Do you know another individual who is in the market for the subject? Please feel free to share it. Thanks a lot for your time invested reading it.
Schedule Here Report this page